A) Tape Measure B) L-square C) Sewing Gauge D) Rulers
A) I, II, and IV only B) I and IV only C) I, II, and III only D) I, II III, and IV
A) I, and III only B) I and IV only C) I, II III, and IV D) I, and II only
A) It is used to snip threads, and they are not designed to cut fabric B) It is used in working with fine details in delicate fabrics and in embroidery work. C) This is popular in zigzagging or scalloped edge or for seam finishes. D) It is used for trimmings, clipping threads, and snipping slashes
A) Start from the tip of the shoulder down to the center of the bust (nipple). B) Start from the top of the shoulder over bust down to natural waistline. C) Start from the nape of neck down to natural waist. D) Start from the top of the shoulder to the natural waistline.
A) Upper Bust, Lower Bust, Waist, Sleeve Hol B) Bust to Bust, Shoulder to Shoulder, Across Back, Full Back C) Bust to Bust, Shoulder to Bust, Upper Bust, Full Back D) Shoulder to Bust, Back Shoulder to Waist, Down Center Back
A) Horizontal, Vertical, Parallel Measurements B) Circumferential, Vertical, Parallel Measurements C) Circumferential, Vertical, Rectangular Measurements D) Horizontal, Vertical, Circumferential Measurements
A) The garment will need minor or little alterations. B) The garment will not fit perfectly the client. C) The garment will be accepted by the client without a problem. D) The garment will fit perfectly the client.
A) To be able to create the best style for the garment. B) To be able to produce a garment that fits perfectly with the client. C) To be able to produce a garment that is inferior and of poor quality. D) To be able to choose proper print of fabric as well as color combinations.
A) C.Take the measuring tape around the waistline. B) D.Taken around the fullest part of the bottom. C) A.Start around the smallest part of the waistline then insert two (2) fingers under the measuring tape for allowance. D) B.Start around the fullest part of the hip/buttocks with two (2) fingers inserted under the measuring tape.
A) 10/2.54 B) 10x2.54 C) 10-2.54 D) 10+2.54
A) 63 cm B) 73.5cm C) 63.5cm D) 83.5
A) Php1,425 B) Php 1,524 C) Php 1,245 D) Php 2,524
A) Php 1,524 B) Php 1,245 C) Php1,425 D) Php 2,524
A) (80)-2.54 B) 80/ 2.54= C) 2.54/ 80= D) 80 X 2.54=
A) Union B) Division C) Subtraction D) Multiplication
A) 1/8 B) 3/8 C) ½ D) ¼
A) 3/8 B) ¼ C) ½ D) 1/8
A) 3 B) 6 C) 4 D) 5
A) mode B) median C) minus D) measure
A) Only clean it when it looks dirty. B) Store it in a damp place to keep it from rusting. C) Use it continuously without any breaks. D) Regularly oil the moving parts and clean the lint from the machine.
A) Because it is specially made to avoid damaging the machine parts B) Because it gives a pleasant smell while sewing C) Because it is cheaper than other oils D) Because it dries faster than cooking oil
A) To protect it from dust and dirt that may affect its function B) To keep it safe from theft C) To prevent children from playing with it D) To make it look more presentable in the sewing room
A) To confirm that the machine belt is tight B) To ensure the needle is sharp and not bent, preventing fabric damage C) To see if the presser foot is aligned correctly D) To test if the machine motor is working properly
A) Oil the presser foot lever B) Replace the motor immediately C) Clean and re-thread the machine properly D) Adjust the height of the sewing table
A) Replace the needle with a new one B) Apply a small amount of sewing machine oil to the moving parts C) Cover the machine with a dust cover D) Tighten the tension discs
A) Oil the balance wheel B) Tighten the table screws C) Replace the needle with the correct size for the fabric D) Clean the bobbin case with a cloth
A) Backstitch B) Chain stitch C) Basting stitch D) Overcast stitch
A) Ruler B) Tape measure C) Tracing wheel D) L-square
A) Needle threader and scissors B) Ruler and tape measure C) Dressmaker’s carbon paper and tracing wheel D) Tailor’s chalk and sewing machine
A) Needles B) Tape measure C) Pins and pincushion D) Tracing wheel
A) Thimble B) Pinking shears C) L-square D) Seam ripper
A) Good choice, because kitchen scissors are stronger B) Wrong, because kitchen scissors may damage the fabric and dull quickly C) Correct, because it saves money from buying shears D) Acceptable, because any scissors can cut fabric
A) Acceptable, because the marks are easy to see B) Good practice, because pens are cheaper than chalk C) Incorrect, because pen marks may stain the fabric permanently D) Correct, because the pen is always available
A) Tape measure B) Dressmaker’s shears C) Gauge D) L-square
A) The size of the sewing room B) Type of marking needed on the fabric C) Price of the sewing machine D) The color of the student’s outfit
A) Measuring B) Holding or securing fabric C) Marking D) Cutting
A) French curve B) Tape measure C) Ruler D) L-square
A) Cause: Wrong fabric → Remedy: Replace with thinner fabric B) Cause: Dust in shuttle → Remedy: Oil the feed dog C) Cause: Loose presser foot → Remedy: Tighten it D) Cause: Incorrect threading → Remedy: Re-thread the machine properly
A) Cause: Loose screw → Remedy: Apply chalk B) Cause: Dull needle → Remedy: Change presser foot C) Cause: Lack of oil → Remedy: Lubricate moving parts D) Cause: Wrong bobbin size → Remedy: Adjust stitch length
A) Cause: Needle too sharp → Remedy: Replace with blunt needle B) Cause: Incorrect thread tension → Remedy: Adjust upper thread tension C) Cause: Thread color mismatch → Remedy: Change to matching thread D) Cause: Presser foot dirty → Remedy: Clean presser foot
A) Cause: Loose belt → Remedy: Tighten screw B) Cause: Wrong presser foot → Remedy: Replace thread C) Cause: Forcing fabric while sewing → Remedy: Let the feed dog move the fabric naturally D) Cause: Wrong bobbin → Remedy: Wind bobbin again
A) Cause: Loose tension → Remedy: Adjust upper thread tension correctly B) Cause: Machine old → Remedy: Buy a new machine C) Cause: Presser foot wrong → Remedy: Clean feed dog D) Cause: Fabric too thin → Remedy: Use thick fabric only
A) Use tailor’s chalk for fabric marking B) Oil the balance wheel C) Ensure the needle is straight and the correct size for the fabric D) Replace the presser foot lever
A) Re-thread the upper thread B) Replace the presser foot screw C) Raise and clean the feed dog to ensure smooth fabric movement D) Change the bobbin case immediately |