A) L-square B) Rulers C) Tape Measure D) Sewing Gauge
A) I, II, and IV only B) I, II III, and IV C) I, II, and III only D) I and IV only
A) I and IV only B) I, and III only C) I, and II only D) I, II III, and IV
A) It is used in working with fine details in delicate fabrics and in embroidery work. B) It is used to snip threads, and they are not designed to cut fabric C) It is used for trimmings, clipping threads, and snipping slashes D) This is popular in zigzagging or scalloped edge or for seam finishes.
A) Start from the tip of the shoulder down to the center of the bust (nipple). B) Start from the top of the shoulder to the natural waistline. C) Start from the top of the shoulder over bust down to natural waistline. D) Start from the nape of neck down to natural waist.
A) Bust to Bust, Shoulder to Shoulder, Across Back, Full Back B) Upper Bust, Lower Bust, Waist, Sleeve Hol C) Shoulder to Bust, Back Shoulder to Waist, Down Center Back D) Bust to Bust, Shoulder to Bust, Upper Bust, Full Back
A) Circumferential, Vertical, Parallel Measurements B) Circumferential, Vertical, Rectangular Measurements C) Horizontal, Vertical, Parallel Measurements D) Horizontal, Vertical, Circumferential Measurements
A) The garment will fit perfectly the client. B) The garment will need minor or little alterations. C) The garment will be accepted by the client without a problem. D) The garment will not fit perfectly the client.
A) To be able to produce a garment that is inferior and of poor quality. B) To be able to choose proper print of fabric as well as color combinations. C) To be able to produce a garment that fits perfectly with the client. D) To be able to create the best style for the garment.
A) B.Start around the fullest part of the hip/buttocks with two (2) fingers inserted under the measuring tape. B) A.Start around the smallest part of the waistline then insert two (2) fingers under the measuring tape for allowance. C) C.Take the measuring tape around the waistline. D) D.Taken around the fullest part of the bottom.
A) 10/2.54 B) 10+2.54 C) 10-2.54 D) 10x2.54
A) 83.5 B) 73.5cm C) 63 cm D) 63.5cm
A) Php 2,524 B) Php1,425 C) Php 1,245 D) Php 1,524
A) Php 1,524 B) Php1,425 C) Php 2,524 D) Php 1,245
A) 80 X 2.54= B) 2.54/ 80= C) 80/ 2.54= D) (80)-2.54
A) Subtraction B) Union C) Division D) Multiplication
A) ½ B) ¼ C) 3/8 D) 1/8
A) ½ B) 1/8 C) ¼ D) 3/8
A) 3 B) 4 C) 6 D) 5
A) median B) measure C) mode D) minus
A) Store it in a damp place to keep it from rusting. B) Regularly oil the moving parts and clean the lint from the machine. C) Only clean it when it looks dirty. D) Use it continuously without any breaks.
A) Because it is cheaper than other oils B) Because it is specially made to avoid damaging the machine parts C) Because it gives a pleasant smell while sewing D) Because it dries faster than cooking oil
A) To keep it safe from theft B) To protect it from dust and dirt that may affect its function C) To make it look more presentable in the sewing room D) To prevent children from playing with it
A) To test if the machine motor is working properly B) To confirm that the machine belt is tight C) To see if the presser foot is aligned correctly D) To ensure the needle is sharp and not bent, preventing fabric damage
A) Oil the presser foot lever B) Clean and re-thread the machine properly C) Replace the motor immediately D) Adjust the height of the sewing table
A) Cover the machine with a dust cover B) Replace the needle with a new one C) Apply a small amount of sewing machine oil to the moving parts D) Tighten the tension discs
A) Clean the bobbin case with a cloth B) Oil the balance wheel C) Replace the needle with the correct size for the fabric D) Tighten the table screws
A) Chain stitch B) Overcast stitch C) Backstitch D) Basting stitch
A) Ruler B) L-square C) Tape measure D) Tracing wheel
A) Tailor’s chalk and sewing machine B) Needle threader and scissors C) Ruler and tape measure D) Dressmaker’s carbon paper and tracing wheel
A) Pins and pincushion B) Tracing wheel C) Needles D) Tape measure
A) Thimble B) Seam ripper C) Pinking shears D) L-square
A) Correct, because it saves money from buying shears B) Good choice, because kitchen scissors are stronger C) Wrong, because kitchen scissors may damage the fabric and dull quickly D) Acceptable, because any scissors can cut fabric
A) Acceptable, because the marks are easy to see B) Good practice, because pens are cheaper than chalk C) Incorrect, because pen marks may stain the fabric permanently D) Correct, because the pen is always available
A) Tape measure B) L-square C) Gauge D) Dressmaker’s shears
A) The color of the student’s outfit B) Price of the sewing machine C) The size of the sewing room D) Type of marking needed on the fabric
A) Cutting B) Holding or securing fabric C) Marking D) Measuring
A) Ruler B) Tape measure C) French curve D) L-square
A) Cause: Incorrect threading → Remedy: Re-thread the machine properly B) Cause: Loose presser foot → Remedy: Tighten it C) Cause: Dust in shuttle → Remedy: Oil the feed dog D) Cause: Wrong fabric → Remedy: Replace with thinner fabric
A) Cause: Dull needle → Remedy: Change presser foot B) Cause: Wrong bobbin size → Remedy: Adjust stitch length C) Cause: Lack of oil → Remedy: Lubricate moving parts D) Cause: Loose screw → Remedy: Apply chalk
A) Cause: Presser foot dirty → Remedy: Clean presser foot B) Cause: Needle too sharp → Remedy: Replace with blunt needle C) Cause: Incorrect thread tension → Remedy: Adjust upper thread tension D) Cause: Thread color mismatch → Remedy: Change to matching thread
A) Cause: Loose belt → Remedy: Tighten screw B) Cause: Wrong presser foot → Remedy: Replace thread C) Cause: Wrong bobbin → Remedy: Wind bobbin again D) Cause: Forcing fabric while sewing → Remedy: Let the feed dog move the fabric naturally
A) Cause: Machine old → Remedy: Buy a new machine B) Cause: Fabric too thin → Remedy: Use thick fabric only C) Cause: Presser foot wrong → Remedy: Clean feed dog D) Cause: Loose tension → Remedy: Adjust upper thread tension correctly
A) Use tailor’s chalk for fabric marking B) Replace the presser foot lever C) Ensure the needle is straight and the correct size for the fabric D) Oil the balance wheel
A) Re-thread the upper thread B) Change the bobbin case immediately C) Raise and clean the feed dog to ensure smooth fabric movement D) Replace the presser foot screw |