A) F1 B) F2 C) F3
A) 5k B) 1ΚΩ C) 10ΚΩ D) 220k
A) 10V B) 5V C) 1µF D) 0V
A) 2ns B) 3 C) 1ns D) 1
A) 100ms B) 5ms C) 10ms D) 20ms
A) .tran B) .op C) Pulse D) .meas
A) None of them B) transient analysis C) Using cursor differences in voltage vs. time plot
A) Exponential rise to steady state B) An exponential decay curve. C) Exponential rise
A) C x R B) R-C C) R/C D) R x C
A) 0Hz B) 1Hz C) 5Hz D) -1Hz
A) 120 B) 10 C) 50 D) 100
A) 1MHz B) 2MHz C) Low frequency D) Highest frequency
A) Frequency B) gain C) High frequency D) Bode plot
A) Half power point (0.707 of peak amplitude) B) half of its maximum power. C) Half point (0.70 of peak amplitude)
A) 12V B) 170 V peak C) 220V D) 120V
A) 10μF B) 100μF C) 1000μF D) 2200µF
A) Bridge configuration with four diodes B) Bridge configuration with two diodes C) Bridge rectifier
A) difference between the maximum and minimm voltage B) Peak-to-peak voltage measurement C) None of them
A) Output power / Input power × 100% B) Input power x output power C) Input power / output power x 100%
A) LM1001 B) LM741 C) LT101 D) LT1001
A) 15V B) 5V C) -15V D) ±15V
A) 10 B) 13 C) 11 D) 12
A) 1V sine wave B) 1 V peak sine wave C) 2V sine wave D) All of the above
A) Frequency at -3dB point from midband gain B) Sine wave C) Bandwidth D) Frequency at 3dB point from midband gain
A) 20ΚΩ B) 10ΚΩ C) 1ΚΩ D) 120Ω
A) High Input Impedance B) CMRR C) Low Output Impedance
A) 1ΚΩ B) 120 C) 220 D) 10ΚΩ
A) Identical signals applied to both inputs B) Apply a common-mode signal C) difference amplifier configuration
A) Connect the inputs B) Apply a small differential input Vd=V-V-VdV+ -V C) Output voltage / differential input voltage
A) drops by 3dB B) drops by -3dB C) 1kHz D) 10kHz
A) Swollen-key B) Sallen-Key C) VCVS filter topology
A) -90 Celsius B) 80 degrees C) -120 degrees D) -90 degrees
A) 4 dB/decade B) Filter order (n) or slope in dB/decade C) All of the above D) -40 dB/decade
A) 0.707 B) 0707 C) 0.770 D) 0.7777
A) 5V B) 12V C) 15V D) ±15V
A) 2kΩ B) 100Ω C) 1ΚΩ
A) 120V B) 15V C) 12V D) 5V
A) Power supply B) AVout/Alload C) AIIoad / AVout
A) Parallel sense resistor with feedback B) Series sense resistor with feedback C) Power supply
A) Colpitts Oscillator B) Wien bridge C) Phase-Shift Oscillator D) Clap Oscillator
A) Period and frequency B) RC time constant C) Frequency-selective componentsi
A) AGC circuit with thermistor B) Use a frequency counter C) Use oscilloscope to see how the output frequency changes D) Amplitude stabilizer
A) oscilloscope to see how the output frequency changes B) Long-term frequency drift measurement C) Use a frequency counter
A) Across the resistance B) Closed loop gain C) Exponential amplitude growth to steady state
A) 50KHz B) 15KHz C) 100kHz D) 1kHz
A) Voltage-Mode Control (VMC) B) PWM feedback control C) negative feedback control
A) (Pin/Pout) x 100% B) Pout x Pin x 100% C) (Pout/Pin) x 100%
A) Damping ration B) Output voltage settling time C) Output voltage not settling time
A) 10μΗ B) 100μΗ C) 1000μΗ D) 1μΗ
A) Tolerance Analysis B) Monte Carlo C) transient analysis D) AC analysis
A) Using . Meas command B) Using.subckt definition C) Using Netlist D) CAD
A) .tran B) .op C) .meas D) .param
A) Plain Text B) SPICE compatible text format C) SPICE compatible image format
A) All of the above B) Symbol creation with subcircuits C) Visual hierarchy D) Top down design
A) Maximum timestep = 1/100 of Highest time constant B) Minimum timestep = 100 of smallest time constant C) Maximum timestep = 1/100 of smallest time constant
A) min= 1e-9 B) gmin=1e C) gmin = 1e-9 D) min= 1-9 E) .options
A) .ic command with node voltages B) .param C) .step D) .TRAN
A) abstol B) Reltol 1e-12 C) abstol 1e-12 D) Reltol
A) Reduce increment size B) Modify gmin stepping C) Refine the mesh D) Tighten Convergence Settings
A) File Export command from the Plot Pane B) Right-click plot, export data as text C) Left-click plot, export data as text
A) V(node1)-V(node2) B) node1 C) Node2 D) .MEAS
A) .meas tran rms RMS V(out) B) .param C) .op D) .tran
A) .tran B) .fft V(out) C) .op D) .AC
A) .AC B) .MEAS P_AVG AVG V(R1)*I(R1) C) .tran D) .param E) .meas avg power = avg (V(n1)*I(R1))
A) Hierarchical prefix with functional description B) Press F4 or the “label net" C) Comment Text for descriptive labels and Net Name Labels/Ports D) Prefix with functional description
A) SPICE directives with comments B) Add comments C) Rename the schematic D) using a text file to document
A) My Documents\LTspiceXVII B) Dedicated folder for each individual circuit project C) Separate folders for each analysis type
A) Clarity, functionality, and portability B) ProjectName_CircuitType_Version C) .measure
A) External Version Control System (VCS) B) Sequential backup with date stamps C) use the .step param command
A) Systematic, multi-analysis comparison B) Systematic node voltage checking C) Verification vs. Validation
A) Error log analysis and stepping B) SPICE Error Log and the Waveform Viewer C) Check for syntax and units
A) Cross-Verification B) Theoretical calculation comparison
A) Systematic process B) Progressive component addition
A) Comparison with datasheet specifications B) Comparison of simulation results against unknown datasheet parameters
A) 100uF B) 1000uF C) 1uF |